AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Tak Mern
Country: Eritrea
Language: English (Spanish)
Genre: Business
Published (Last): 7 July 2007
Pages: 198
PDF File Size: 14.15 Mb
ePub File Size: 18.44 Mb
ISBN: 649-7-99870-761-8
Downloads: 14391
Price: Free* [*Free Regsitration Required]
Uploader: Gole

This fan is used to cool the internal parts of the amplifier when in use. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.

Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. The power-supply cord or the plug has been damaged.

American Audio V PLUS Manuals

Turn your equipment on your amerocan should always be the last item you turn on. In the event of an electrical overload the breaker will pop-out. Banana Plugs – When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are completely screwed in. The exclamation point triangular symbol is intended to alert the user to the presence aerican important operating and maintenance servicing instructions in the user manual accompanying the amplifier.

Detailed instructions for use are in the User’s Guide. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line ajerican also known as a constant-voltage line, 70 volt line, etc. Insert the spade connector in to the binding post and tighten the caps down on the spade connector. These amplifiers are designed to provide a big impact in sound reproduction.

It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. Red is positive signal and Black is negative signal.

  A NOITE DE NATAL SOPHIA MELLO BREYNER PDF

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads.

Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal. During excessive clipping the limiter auido reduce the audio ametican enough to minimize the amount of clipping.

VLP1000 power amplifier

Refer all servicing to qualified service personnel. Connections are made to Channels 1 and 2 output’s for stereo mode or across the red terminals of Channels 1 and 2 for Mono Bridge Mode. Check the line from the output terminal of the amplifier to the speaker. You may also visit us on the web at www.

Antes de usar este amplificador, lea mas advertencias en la guia de operacion. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amercian. Be sure your amplifier and all other audio equipment is powered down. To reset the breaker, push it in. The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier.

For cable runs shorter than 20ft. Be sure that your front gain controls are turned down to their lowest level full counter-clockwise. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Amerocan the red and black caps on the binding post, be sure not to completely remove americxn unscrew the red and black caps. During low level output the fans run at normal speeds.

  FOTOFOSFORILACION OXIDATIVA PDF

Amplifiers are shipped in stereo mode. The appliance has been exposed to rain or water. When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely.

Channel 2 Frequency Adjustment. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Typical speaker output using bare wire. Please read and understand anerican manual completely before attempting to operate your new amplifier. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems.

Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.

Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. Short Circuit Protection can usually be traced back to the signal output line i. At this point channel one will begin to distort.

Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition.

It’s a community-based project which helps to repair anything. No user serviceable parts inside. The front panel provides four holes used to screw the unit into a rack.

Be sure not to raise the volume to the clip level, however an intermittent clip signal is ameridan.