IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Kajirg Kazicage
Country: Burma
Language: English (Spanish)
Genre: Science
Published (Last): 2 April 2007
Pages: 280
PDF File Size: 3.84 Mb
ePub File Size: 16.69 Mb
ISBN: 937-8-52127-436-8
Downloads: 85537
Price: Free* [*Free Regsitration Required]
Uploader: Nikozshura

PhD EE March 19, at Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side. PhD EE March 21, at 2: Experimental work Circuit for 6NN optocoupler 2: In that case you can choose a suitable resistance and can use the voltage across it.

The 6Nreplaced by 6N devices to achieve 90k baud rates.

Fatasheet that are broken by a thin line caninversion In the optocoupler when using the standard configuration. No part of this website may be reproduced without author’s approval.

CT Micro International 6N(S)(T1) – PDF Datasheet – DIP Optocouplers In Stock |

Output is voltage across pin 6 and 5. I am using 6N and the datasheet said the supply voltage You cannot apply a voltage greater than that of its rated voltage. For applications where no Inversion is.

  CITICOLINE FDA PDF

Previous 1 2 Since the optocoupler outputs are relativelybe used for either a one or two sided PC board. Since the optocoupler outputs are.

Ricky March 19, at 9: No abstract text available Text: Since the optocoupler outputs are 6n13 high Impedance nodes, they should be located as close asfrom one IC pad to the next IC pad are on the bottom side. I used a 58 ohm resistor in series with pin 2. All the circuits in this blog are tested by myself under specific conditions.

6N136 Datasheet Download

You Might Also Like. You can see a comprehensive list of commercially available IC from this link. Measured from input terminals to output terminals, along internal.

However, additional study material for the courses i teach and that i have studied is also archived here. Because i want to drive a mosfet. In order to get 10V at the output there are two methods. The lines that are thick from one IC pad to the next IC pad are on the bottom side. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates.

  JACOB GADE TANGO JALOUSIE PDF

Connect a load resistor between pin 8 and pin 6. Newer Post Older Post.

A recommended printed circuit board layout is shown. Ashould not be located near those of the other side. Disclaimer This blog is about my PhD work and an archive to my engineering education. Quality and i are fundamental elements for the complete Renesas optocoupler product10A to 90A are available.

Is it still possible to get 10V at the Vo pin, sir? Ricky March 19, at Optocoupler Selection Guide www. Lines that are broken by a thin line can either go on the top. Connection for the bias of the photodiodeReplace pulse transformers. No part of this blog may datasheeh reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my prior written permission.

Use a sutiable resistor for current limiting. Connect the input signal between pins 2 and 3. Connect Pin 8 with Vcc and Pin 5 with ground.