KEYENCE LS-7601 PDF

Precautions for CE Markings Keyence confirms that the LS Series . LS- Photoelectric Sensor or Proximity Sensor Timing input signals are sent. Find great deals for 1 PC KEYENCE Ls CCD Laser Micrometer. Shop with confidence on eBay!. LS High-performance controller. Visible measurement pointController with Target Viewer. High-durability CCD . The LS Series measures the outer diameter of a fiber continuously and .. E-mail: [email protected]

Author: Fenrigami Maulmaran
Country: Fiji
Language: English (Spanish)
Genre: Travel
Published (Last): 2 December 2014
Pages: 418
PDF File Size: 6.83 Mb
ePub File Size: 1.11 Mb
ISBN: 627-3-28670-945-1
Downloads: 11793
Price: Free* [*Free Regsitration Required]
Uploader: Meztilkree

OUT1 Repeat steps 7 and 8 until all the digits are input. Page Chapter 5 Function Settings Note: Sets the tolerance mode to use either reference values or thresholds. Possible Output Settings The following output settings are possible.

LS – Controller, with Monitor Function | LS series | KEYENCE UK & Ireland

To turn ON the backlight again, press any control panel key or remote control console key. Furthermore, a selected program can be initialized. Page 30 Chapter 1 Getting Started 3 Connect the cable between the controller and measuring head.

Chapter 6 Environment Settings RSC Take the following steps to make the communication settings for the RSC interface and relative settings for peripheral devices. AmazonGlobal Ship Orders Internationally.

Appendix R Reference value mode Calibration settings correct for this error. Erect the legs and use the AC power supply stand if required. Refer to Copying Programs on page for details. Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Width with Two Measuring Heads for Larger Objects A sheet cannot be located in the measuring area of a single measuring head if the width or diameter of the sheet is excessively large.

OUT2 R q cr External synchronization: Page 71 Chapter 5 Function Settings Area Settings Area settings are used to determine the measurements taken from a variety of objects placed in the beam. The LS Series will return an error response if a command received is different in tolerance mode. This function is convenient for zero-point calibration for a variety of targets.

  ADRIAN SLYWOTZKY PDF

The results of difference checks will be output externally, provided that DIFF function output settings are made properly in advance.

Chapter 5 Function Settings 08 09 10 Note: For the arrangement of each terminal, refer to pages and The average value during keywnce sampling period specified is displayed and output. Mounting holes Used to mount the measuring head. This section provides information on the details and methods of output settings.

1 PC KEYENCE Ls-7601 CCD Laser Micrometer

Chapter 5 Function Settings Setting Screen The following section provides information on setting items. Otherwise, the settings may be partially or completely lost.

Baud rate, parity, stop bit, data length, data mode, and data transmission mode of the RSC interface. The maximum value measured by the LS Series in continuous measurement operation is displayed and output. Check that the wiring specifications of the communications cable are correct. This function makes it possible to prevent kkeyence measurement of abnormal values that may result if dust or oil is stuck on the measuring head.

Page 84 Chapter 5 Function Settings Calibration Settings The measured value of an target may have a delicate error due to the surface condition and angle of the target. See and discover other items: Familiarize yourself with this section before using the LS Series.

There was a problem completing your request. List of Optional Accessories Page 86 Chapter 5 Function Settings Calibration Type Selection The following section provides information on how to set the calibration type for each area. Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Eccentricity In the following kejence, the outer diameter and eccentricity of the roller is measured while the roller moves. Setting Range The following modes are selectable.

  HX750 MANUAL PDF

Shopbop Designer Fashion Brands. Chapter 8 RSC Setup Serial Commands The following section provides information on command formats that are used to make setting changes. Page Chapter 10 Troubleshooting Error Messages The following section explains error messages that will be displayed if the LS Series has errors while in operation.

Changes the display unit of measured values. The types of measured values held vary with the MEA-Mode.

The focus monitor range is the distance between the receiver and target in the measuring area. TR Base Used to mount the transmitter and receiver. T1-A will be lit. Its functions and performance are not guaranteed under said conditions. When you write a control program, check that the program will enable the external device to send the next command after the external device confirms the response from the LS Series.

The following section provides information on how to mount the measuring head with or without the TR base employed, along with mounting conditions required. The following types of measured value output are possible. Learn more about Amazon Prime. Chapter 5 Function Settings Change of Edge Detection Threshold The following section provides information on how to make threshold changes for the measurement of highly transparent objects.

The LCD monitor is operable through the panel keys as well as the remote control console. Setting Range The range is initially set to — Page 50 Chapter 3 Easy Setting Guide Statistical Processing In the following example, the values calculated from the measuring data are: