IGCT DATASHEET PDF

The IGCT is a gate-controlled turn-off switch which turns off like a transistor but conducts like a thyristor with the lowest conduction losses. Figure 1 shows turn- off. Basic design rules and handling / application recommendations for IGCT Gate Units .. The connector X1 is specified in the corresponding IGCT data sheet. mm. Height h. ± mm. 41 mm. Width IGCT w. ± mm. mm. 1) Maximum rated values indicate limits beyond which damage to the device may occur.

Author: Tunris Mezshura
Country: Liberia
Language: English (Spanish)
Genre: Sex
Published (Last): 27 February 2005
Pages: 71
PDF File Size: 19.93 Mb
ePub File Size: 18.2 Mb
ISBN: 299-7-32512-471-5
Downloads: 63205
Price: Free* [*Free Regsitration Required]
Uploader: Akimi

It is demonstrated herein that the models developed are computationally effective; however, in the case of all three systems either only partial system models are used or there are remaining simulation issues to be resolved. Thermal management is considered an enabler for the technologies likely to appear on an AES. datashedt

The system-based tests were conducted with the help of a Real Time Simulator RTS to facilitate Control Hardware-in-the-Loop simulations and igc of the surrounding power system components. Are you looking for support or purchase information?

However, this effort was focused on simplified models to serve the needs of interactive early stage design. This ability to manage technological change has helped achieve superior capability. This procedure is aided through the use of empirical and experimental correlations that have been documented extensively in the literature.

Observing the merits of beginning at a more superficial F-FMEA are evident, mainly in the fact that the current research is centered around modeled representative systems with more generic than specific hardware information.

The US Navy continues to support applied research on the design, development, and simulation of their future fleet of all-electric ships AES.

A different approach would increase training costs and thus overall costs. An extension of impedance measurement units IMU to the medium voltage MVmegawatt-class converter levels would provide significant benefits to the U.

Integrated gate-commutated thyristors (IGCT)

The system structure is very similar datasheer that of the induction motor and the employed control algorithm is also very close to that used in the motor controller. However, they do have a parasitic impedance to ground that can be measured by VNA measurements while not energized and by fault tests when in operation. Additional impedances to ground can be added for calibration purposes. Power electronics converters of the megawatt class need to be characterized regarding their capacitive, inductive, resistive and radiative coupling to the ground plane.

  BUXWV 149 PDF

This model wraps a model made by ACSL. The measures impedance characteristics support determining the stability related system properties. The emphasis is laid on a F-FMEA which serves as the most appropriate method to start analysing failure cause and effects in a novel system such as the zonal shipboard power distribution architecture studied. Learn more I agree. The task will take advantage of the infrastructure at FSU-CAPS to facilitate the proposed component technology development and prototype testing and validation with the systems view in focus.

In this model Rs and Ls indicate the equivalent armature coil resistance and inductance respectively. The rotor of a permanently magnetized synchronous machine can have the magnets applied either on the rotor surface or buried deep into the rotor.

An analysis framework will be developed along with supporting software tools which takes into account the controllability of localized energy storage via the supervisory control approach and interface characteristics. The objective of this report is to set forth a igft of time-domain models for the early-stage design study of shipboard power systems, datasjeet to demonstrate their use on various system architectures.

The complete list of correlations and the steps required to determine the correct correlations are presented in the Appendix. Furthermore, the guidelines and rules extracted through this task will be integrated into the S3D environment to enable applying well-established engineering principles to the automation of design evaluation.

However, this average value does not capture the magnitude of peak waste heat during transient situations. The voltage control loop drives the error in the output voltage to zero by generating a current command through the use of a PI regulator with decoupling and feed-forward control. On a highly dynamic, controls-oriented ship, such as the notional AES, steady-state values provide little utility from a reconfiguration or system failure perspective.

Asymmetric and reverse conducting. Also addressed are results specific to future trends of cable insulation and future standards. The objective of this report is to set forth a group of time-domain models for the earlydesign stage study of shipboard power systems. In addition to developing notional designs for the 10, ton surface xatasheet, the ship design project provided important feedback to the S3D software development team.

Typically the cooling fluid is saltwater seawaterfreshwater, or chilled water. When sufficient recommendations for change are made, they will be incorporated and a new revision will be released.

  CALAMANSI FOR SKIN ARTICLE PDF

In general the number of slots is large for distributed windings typically 6 per phase. VTB-Matlab interface uses and requires a registered copy of Matlab to be loaded onto the host computer. This project report details approaches and results of testing the first medium voltage, megawatt-power level IMU.

IGCT (Integrated Gate-Commutated Thyristor) | ChipFind Datasheet Archive |

The PMSM are usually considered a linear device over its entire operating range of torque and speed, with practically linear speed-torque characteristic. The Office of Naval Research is developing science and technology for advanced electric ships that utilize an integrated power system. The user selectable parameters include the conductor materials, and the size and physical arrangement of the conductors.

Indication of relative vulnerability of datsaheet sections, components and subsystems to focus studies on their respective faults and failures An understanding of the need for detailed hardware information which would eventually lead to a more exhaustive hardware FMEA H-FMEA. Iterate until total ship mission effectiveness requirements are met.

The load is time dependent, and it is characterized by a look up table in an Excel spread sheet. The individual modules implemented for model will allow the user to comprehensively ogct different methods of fault detection algorithms while providing useful insight into behavior of different modules.

The circuit consists of an ohmic resistor and a finitelength Warburg Element in series. The model implementation is presented datasbeet validation studies have been performed which show very good modeling performance.

Figure 1 depicts the power converter topology used to implement the inverter module.

Integrated gate-commutated thyristors (IGCT) | ABB

And this has been successful. The polarity of the voltage is the same as the current flow direction. The component models are highly simplified abstractions of shipboard power system components.

This task will also involve collecting and maintaining the relevant data on HTS cables that would be necessary to update the electrical models developed as the technology matures and new design features are added. It generates the switching commands for the power semiconductors.

The breaker state changes from closed to arcing, when the RMS current through it exceeds its current rating.